OPINIONFoodservice

Keeping Refrigeration Costs Down During the Summer

Tips to save on energy bills all season long
inside of a warehouse
Photograph: Shutterstock

NEW LISBON, Wis. — “Close the door behind you! You’re letting all the cold air out!” We all heard this in the summer as kids, but little did your parents know, that exact piece of advice applies to your business’ walk-in coolers, freezers and other refrigeration units.

Hot summer days increase traffic to your walk-in cooler for bottled water or beer, but with that extra traffic comes additional heat and humidity. At Leer Inc., we calculated that a smaller walk-in cooler or freezer can cost roughly $5 per day to operate, and a larger walk-in as much as twice that. These costs rise as humidity, heat and traffic in and out of the cooler rise. But there are ways to limit the impact.

Learn Proper Loading Technique

The warmer the ambient temperature around a walk-in, the warmer the air that enters the cooler every time the door is opened. When possible, try to avoid loading the cooler during the hottest part of the day. Instead, aim for mornings or evenings when it's cooler in the store and out.

Regardless of what time the walk-in is loaded, there are a few tips you should follow.

  • To echo your parents’ advice: Close the door behind you.
  • While loading the walk-in, minimize the number of trips in and out, and do not prop open the door. Every time the door is opened, hot air enters, requiring the refrigeration to cycle more often or longer, and each of these cycles equates to additional costs.
  • While stocking the cooler, be sure to maintain proper spacing around the evaporator coils (in simple terms, the fans) and the walk-in wall panels to allow for proper air flow. No product inside the walk-in should be stacked higher than the lowest part of the evaporator coils nor stacked in front of them. Likewise, all product should be stored at least 1 inch away from the wall panels. This will prevent excessive frost and ice buildup and will help make sure the coil is properly cleared during defrost, which will keep the walk-in running smoothly and efficiently.

Maintain Cleanliness

If you’re only going to listen to one tip from this post, it should be this: Keep your equipment clean.

A dirty condenser coil will result in a less efficient refrigeration system and force longer cycle times to reach the desired temperature. If the condenser coils are dirty enough, it’s possible it may not be able to cool down to the desired temperature, which is why keeping your condenser coils clean is so important.

Why exactly does a clean condenser lead to a more efficient cooler? Technically, the refrigeration system is not pumping cold air into the walk-in, but rather removing heat via the refrigeration. The condenser coils’ job is essentially to release the heat outside. If they’re dirty, less heat can escape outside and therefore more heat stays in the system. When heat is in the system, the refrigeration cycles longer and in the end, costs you more money.

Keep Up With Maintenance

Similarly, preventive maintenance is also key to reducing operational cost and increasing reliability. Think of it the same as taking care of a car. We maintain our vehicles with oil changes, tire rotations, and inspections to increase reliability, prevent costly repairs and extend the life of the car. Refrigeration equipment is no different. Proper preventive maintenance will ensure the most energy efficient operation. This should include:

  • Regularly clean and inspect condenser and evaporator coils.
  • Inspect copper lines to make sure nothing is rubbing or vibrating in a way that might cause a leak.
  • Inspect wiring for loose connections and frayed or burned wires.
  • Inspect electrical components, such as contactors, for pitted or burned contacts.
  • Ensure the door sweeps are in good shape.
  • Inspect gaskets on all service/entry doors for proper seals.
  • Inspect glass door gaskets and check for proper seals.
  • Be sure strip curtains are in place and not damaged.

Any warm air and humidity that you keep out of the walk-in will equate directly to cost savings. That’s why most of the maintenance tips revolve around ensuring your cooler has a tight seal.

Use Proper Settings

If you don’t need your walk-in freezer at -20 degrees F, turn the temperature to a warmer setting. Same goes for a cooler that is set colder then needed. There are some items, such as ice cream, that require special temperatures, but otherwise we often see walk-in coolers and freezers set to temperatures lower than needed. Choosing a warmer temperature within the safe zone for your items helps prevent excess refrigeration cycles and cycle times, which saves money.

All control settings, including temperature and defrost times, should be optimized. Some of this can be done by store associates, but the majority of it should be performed by a refrigeration contractor.

Select Proper Accessories

It’s very common for walk-ins to include lights. Their impact on the overall running costs are minimal, but every little bit helps. We recommend using LED lights, which use less electricity than both fluorescent and incandescent light bulbs. Depending on the walk-in layout, it's possible lights do not need to be turned on all the time. Instead, lights can be connected to motion sensors to make sure lights are on when people are present and turned off when the cooler or freezer is not occupied to save on energy costs.

HVAC-R Is a Team

Control the surrounding ambient temperature of the walk-in as best you can. Maintaining temperature and humidity around a cooler or freezer will help minimize introduction of warm air and humidity every time the walk-in is accessed.

Walk-in coolers and freezers are great for keeping product cold but are not designed to remove humidity. Air conditioning systems will do a much better job and will be more cost effective. Therefore, a final tip: Make sure your air conditioning system is operating properly.

In the hottest days of summer, your walk-in will most likely require additional cycles and longer cycle times to maintain the proper temperature. But by following these tips on how to keep refrigeration costs down during the summer, you’ll put your business in the best possible position to save on energy costs all season long.


Geoffrey Gould is the product marketing manager at Leer Inc. and lead contributor to the company’s Temperature-Controlled Storage Solutions blog. Connect with him on LinkedIn.

Want breaking news at your fingertips?

Get today’s need-to-know convenience industry intelligence. Sign up to receive texts from CSP on news and insights that matter to your brand.

Related Content

Trending

More from our partners